DIY BATHTUB INSTALLATION.

DIY Bathtub Installation.

DIY Bathtub Installation.

Blog Article

Book A Service Call

Just how do you actually feel about Tools You Need to Install a New Bathtub ?


Installing A Bathtub
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open up a wall to remove the old tub and also position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the new one. Make sure you have actually certified yourself for the work as well as are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Chances are you might need a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new bathtub in your washroom if you have currently gotten a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list ought to consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
    Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final position.

    Removing Old Taps


    If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
    Before moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Setting up the Bathtub


    Making use of both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
    The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level reads degree.
    To set up taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
    Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow outlet and also the typical electrical outlet for leaks.
    Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used at the very least when as this will settle it right into its last position.

    Suitable New Touches


    If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
    If you require to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next off, position the tap in the installing opening in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Protect the faucet in place with the producer supplied backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath as well as the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
    You can choose from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealant can break fairly early if you do not consider this movement prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a keen person who reads on How to Install a Bathtub Yourself, I thought sharing that segment was a good idea. Don't hesitate to take a moment to share this page if you appreciated it. Thanks for your time. Kindly come by our blog back soon.



    Rates

    Report this page